All ideas

Showing 160 of 160

Toggle Between v12 Result Grid and v24 Result Grid

The v12 Result grid was a much simpler, leaner, and straightforward method to data processing for the excel oriented layout it had. With the v24 Result grid, we CANNOT select any of the columns independently as previously on v12. This completely r...

Guest 8 months ago in UI 5 Will not implement

6 VOTE

Add a button that resets the Input Grids or Results grids to visible location on screen

When using AutoPIPE on laptop connected to a docking station or additional monitors, then removed to just using a laptop screen may cause the input / results grids to not be shown in the visible area. The grids are hidden out of screen view. Recom...

Mike Dattilio about 2 years ago in UI 0 Needs review

12 VOTE

When exporting a model, the user should have the ability to select which nodes are exported based on the type of element it represents.

When creating stress isometric drawings, my team typically exports a .dxf file of the AutoPIPE Model. We are only concerned with nodes that represent support locations, however, there is no option to export only support nodes. Having this option a...

Guest about 4 years ago in AutoPIPE Pipe Stress 1 Future consideration

6 VOTE

Increase allowable number of internal data points from 10,000 to 100,000 or more

AutoPIPE's analysis is blocked if total number of points (piping points+ soil points + frame nodes) is greater than 10,000. Suggest to increase the limit number of node points from 10,000 to 100,000 or more.

Mike Dattilio about 2 years ago in Modelling 0 Future consideration

3 VOTE

Bring back the Bentley AutoPIPE User Accreditation Program

As per the note in read on the top of this page, please bring back the user accreditation program

Hubert Velten about 1 year ago in AutoPIPE Pipe Stress 1 Needs review

3 VOTE

Flange Ansi check as per UG-44: setting a user ratio for each rating

Ansi/kellogs method is a widely used way to check flange joint, but different standard, or client specification could use different allowable. Now the ASME BPVC VII UG-44 suggest 2.2 for B16.5 #150 and 1.5 for most of the others; DNV suggested 1.5...

Gianludovico Spizuoco about 1 year ago in Reporting 1 Future consideration

5 VOTE

Wind load acc. to EN 1991-1-4 (Wind)

In the European Union we design wind loads acc. to EN 1991-1-4 (Wind), hence it would be nice if wind loads are implemented as in other pipe stress analysis programs.

Guest almost 2 years ago in AutoPIPE Pipe Stress 0 Needs review

4 VOTE

Ring Tool - Ability to define Branch Type for each projection angle

Currently, the Ring Tool is limited to apply all Run Branch types or all Tee Branch Types. Why doesn't the tool allow the user to independently define which nodes need to be tees or runs? See attached screenshot for details.

Sujaan Ahamed Fareed over 1 year ago in Modelling 0 Needs review

1 VOTE

支架选择中增加固定支架选项

管系应力分析计算时，经常需要设置固定支架，该支架承受垂直、水平、径向三个方向（即轴系中 xyz三向）的力，且此处三向位移均约束 0。现有支架选项只能通过滑动支架+限位支架组合实现该功能。但是计算结果输出到路草支吊架软件时，会自动视别为两个支架。 When calculating the stress analysis of the piping system, it is often necessary to set a fixed bracket, which bears the f...

Guest 5 months ago in AutoPIPE Pipe Stress 1 Needs review

10 VOTE

Increase tag length or remove the restriction altogether (like Caesar II)

The current max length of tags is 36 characters. Tag is meanwhile just about the only play where we can save some element-specific information. For example in the case of a Support I would like to save AT LEAST the following:1) The designation of ...

Guest about 4 years ago in AutoPIPE Pipe Stress 0 Future consideration

Please enter your email address

FILTER BY CATEGORY