AutoPIPE Ideas Portal

Welcome to the AutoPIPE Ideas Portal. We value your feedback, and our team regularly reviews your ideas and considers them for future improvements to our products and services.

You have 3 options for providing feedback:

  1. VOTE for an existing idea. The popularity of an idea helps us understand its importance to the community.

  2. COMMENT on an existing idea. We want to hear your unique point of view.

  3. ADD a new idea. You can always submit a new idea if no existing one describes your suggestion.

When you add, vote or comment on an idea you will also be subscribed to that idea and receive status updates. Please note we may merge or rename ideas for better clarity for the community. Thank you for your support and feedback.

ADD A NEW IDEA

Modelling

Flexible Joint Step Function Stiffness

Looking for an update to flex coupling input box to better model flexible coupling behavior. Flexible joint additional inputs (see attached) 1) Max angle of deflection for flex joint 2) Two stiffness inputs for bending stiffness. Stiffness changes...
Guest about 3 years ago in Modelling Future consideration

Add new support type for wall and roof penetrations

We typically model wall and roof penetrations as guides with clearance gaps of approximately 0.5 to 1.5 inches in all directions. These modeled clearances are then used to verify load transfer and confirm that the gaps are adequate at each penetra...
Karim Rinawi 7 months ago in Modelling Reviewed

Add Victaulic fitting

AutoPIPE can model a Victaulic fitting using a number of approach mentioned here . However this is a very difficult and demanding process. Not to mention, that in some case there are converging issues related to multiple Flexible joints on connect...
Mike Dattilio about 3 years ago in Modelling Future consideration

Increase allowable number of internal data points from 10,000 to 100,000 or more

AutoPIPE's analysis is blocked if total number of points (piping points+ soil points + frame nodes) is greater than 10,000. Suggest to increase the limit number of node points from 10,000 to 100,000 or more.
Mike Dattilio over 3 years ago in Modelling Future consideration

Rotate command should update Anchor translational and rotational stiffness components

When an Anchor support is rotated using the Rotate command in AutoPIPE, the translational and rotational stiffness components do not update to reflect the new orientation. This leads to stiffness being applied in the wrong directions relative to t...
Shrey Sharma 6 months ago in Modelling Reviewed

Add Node Annotations to stress isometric

AutoPIPE's Node Annotations (Insert > Node Annotations) are not able to be printed on a Stress Isometric. Using the "save isometric drawning" prompt, we have the option to isert annotations (but it's not a good way to do it), and it's not relat...
Guest almost 3 years ago in Modelling Needs review

Add Feature to Allow Specific Gravity to be Changed for Different P/T Cases

At the moment, specific gravity is entered under Pipe Properties and cannot be changed for different pressure/temperature load cases. If there are different load cases, where a section of the model may be filled with water in Case 1 but filled wit...
Guest about 1 year ago in Modelling Needs review

Ring Tool - Ability to modify angles in the Ring Tool dialog

When a user defines custom projections in the Ring Tool dialog, and then realizes they need to add an additional angle, it is not possible. The current method requires the user to clear out the custom angles defined and reenter the custom defined ...
Sujaan Ahamed Fareed over 2 years ago in Modelling Needs review

display miter bends

When a bend is a miter display with the number of cuts or at least just one cut so they do not look like formed bends.
Kevin Koorey about 3 years ago in Modelling Needs review

Piping comparison feature

When systems are revised it would be useful if a user could import new files from designers and see them directly on top of existing systems. This would allow a user to be able to visually see and measure changes. Updated files can be imported but...
Guest 10 months ago in Modelling Needs review