AutoPIPE Pipe Stress

Showing 64

Copy to clipboard button for floating load window

It would help users trying to extract maximum loads from the floating loads window if it included a copy to clipboard button which copied the loads, directions and load case to the clipboard. Currently, users have to manually type this and this ca...

Sujaan Ahamed Fareed 15 days ago in UI 0 Needs review

1 VOTE

Add the plastic moment reduction factor criteria for the LCC calculation

As per section 5.4.6.8 of the DNV ST F101_2021 Version, the LCC calculation is modified by including the plastic moment reduction factor due to the maximum vertical point load. This would be a good approach to have more realistic and reliable LCC ...

Guest about 2 months ago in Code 0 Needs review

5 VOTE

Add features to include Type A/B fitting pressure factor for En13480 piping code

Add options into application that accommodates En13480 table A.2 specification for all fittings per En10253 requirements to define pressure factors to be applied to fittings of Type A and wall thickness requirements of fittings of Type B. Add opti...

Shrey Sharma 3 months ago in Analysis 0 Needs review

1 VOTE

Autosave the file after 1 minute

Kindly refer to the discussion in regard to the case no. CS0345238, regarding introducing autosave option after every 1 min or less. Similar feature is available in other stress analysis software can't same be availed in Auto PIPE as well, because...

Guest 3 months ago in AutoPIPE Pipe Stress 1 Needs review

14 VOTE

Support Report: Remove all global results from Local columns

For V-stops and Hanger support types, the Support report prints global values as local values. Example, see attached image. Notice the Global axis direction is different from the indicated pipe's local axis direction. Next notice the support's Loc...

Mike Dattilio 3 months ago in Reporting 0 Needs review

6 VOTE

Add ability to group analysis sets which represent different analysis cases

Piping Stress, Pipe Support, and Foundation load generation require different analysis conditions using different seismic loads to meet differing code requirements. Currently, this is difficult to manage in the same autopipe file as users may have...

Sujaan Ahamed Fareed 3 months ago in Analysis 0 Needs review

1 VOTE

支架选择中增加固定支架选项

管系应力分析计算时，经常需要设置固定支架，该支架承受垂直、水平、径向三个方向（即轴系中 xyz三向）的力，且此处三向位移均约束 0。现有支架选项只能通过滑动支架+限位支架组合实现该功能。但是计算结果输出到路草支吊架软件时，会自动视别为两个支架。 When calculating the stress analysis of the piping system, it is often necessary to set a fixed bracket, which bears the f...

Guest 4 months ago in AutoPIPE Pipe Stress 1 Needs review

1 VOTE

Apply wind Shape factor to pipe properties instead of everything as it varies due to geometry in AS1170.2

You currently only have 1 place to input the Wind shape factor and this is applied to all pipes but the value is different for each diameter in Accordance with AS1170.2. This value could be input in the pipe properties for individual pipe sizes, t...

Paul Nielsen 5 months ago in Analysis 0 Needs review

1 VOTE

Wind Load calculator for AS1170.2 for Australia

This would save time with setting up wind loads, anyone designing in australia would benefit. Competitors software already has this

Paul Nielsen 5 months ago in Code 0 Needs review

1 VOTE

ADD DVS (DVS 2210/DVS 2205) code

The DVS code is a technical code which includes fundamentals for the design, calculation, prefabrication and assembly of industrial piping made of thermoplastics and laid above ground. More clients are requesting for this code and would be a great...

Guest 5 months ago in AutoPIPE Pipe Stress 0 Needs review

Please enter your email address

FILTER BY CATEGORY